MATS CB automatic transfer switch
Keywords:
Keywords:
MATS CB automatic transfer switch
Category:
Tel:
MATS CB automatic transfer switch
Product Description
Eaton MATS CB The automatic switch transfer device uses the most basic design to provide a reliable and comprehensive dual-power transfer switch device.
CB Level uses circuit breakers as actuators, PC Level uses isolating switches as actuators.
The device uses an automatic open-circuit switching method, suitable for applications that require backup power input and can accept instantaneous power interruption during switching. 。
Product Features
1、 Modular, intelligent design, small size, simple structure ;
2、 Single motor drive, simple and stable drive, small impact force, low noise;
3、 The motor does not work in a steady state, low power consumption, high reliability;
4、 The actuator has mechanical and electrical double interlocks, reliable switching;
5、 Automatic detection of undervoltage, phase loss, and undervoltage, and automatic switching, self-starting and self-recovery;
6、 CB level uses circuit breakers as actuators and has line protection function; PC level uses load isolating switches as actuators;
7、 Manual /automatic switching function;
8、 The switching time can be effectively set online;
9、 With fire linkage function (standard), status feedback (standard);
10、 When a fault occurs on the load-side line, MATS does not switch;
11、 Displays various operating statuses.
Working principle
1、 The device is controlled by a motor to drive two circuit breakers /The switching of the main and backup power supplies is achieved by the closing and opening of the load isolating switch.
2、 The device has manual /two operating modes, and a manual/automatic switch is provided on the panel for selection.
3、 When automatic is selected, the controller detects the status of the normal and backup power supplies. When the normal power supply fails and the backup power supply is normal, it automatically switches to the backup power supply.
4、 When the normal power supply is restored, it switches back to the normal power supply, realizing the function of self-starting and self-recovery. When manual is selected, the power of the controller is cut off, and the manual operation knob is used to perform the closing and opening operation of the normal and backup power supplies. Mainly used for maintenance or device operation in non normal condition state when in emergency use case 。
5、 The MATS series dual-power automatic transfer switch also has a fire linkage function, that is, when the fire signal is valid, the controller automatically runs the normal and backup power supplies in the off state, thereby cutting off the normal and backup power supplies. When the fire signal is removed, the dual-power automatic transfer switch must be re-powered and reset or reset with the manual/automatic switch (switching the manual/automatic switch from manual to automatic once) before it can run automatically again.
6、 The device has normal and backup power supply status feedback output, which is a passive contact (normally open).
7、 For devices that generate electricity from the mains (only for MATSB-series), its working principle is that when the mains fails, the controller sends a start generator signal. When the voltage generated by the generator reaches normal, it switches to the backup power supply. When the normal mains power supply is restored, it switches back to the mains power supply and stops the generator operation. The rest is the same as the mains power switching.
Core Functions
1、Integrated structure
2、Standard fire linkage function
3、Voltage and phase monitoring
4、 0-6 second delay (DIP switch)
5、Switch position indication
6、Manual / automatic switching mode
7、Neutral line (misconnection) alarm; LED light
Operating Environment
Temperature :-25℃~70℃
Altitude :<2000m
Humidity :Average monthly humidity <90% when the average monthly temperature is +25℃
Pollution Level :Level 3
Protection Level :IP20
MATS Series Product Model
| Order Number | Model |
|
CSD00003
|
MATSA G1/A20 3 CB
|
|
CSD00019
|
MATSB G1/A20 3 CB
|
|
CSD00035
|
MATSC G1/A20 3 CB
|
|
CSD00010
|
MATSA G1/A100 3 CB
|
|
CSD00028
|
MATSB G1/A160 3 CB
|
|
CSD00037
|
MATSC G1/A32 3 CB
|
Previous Page
Next Page
Previous Page
MATS PC-grade automatic transfer switch
Next Page
Online Consultation
Please leave your contact information, our professionals will contact you as soon as possible!